Released new version H-JTG V1.1 RELEASE (Build 20100601) RELEASE
1 - Added the support to Widows7, new USB drivers are provided;
2 - Added the production mode in H-Flasher to improve the efficiency for production;
3 - Added a new document to illustrate how to add a new NAND flash drivers;
4 - Updated the NAND flash drivers for S3C6410, corresponding H-Flasher configuration file is provided;
5 - Updated teh NAND flash drivers for PXA3XX series. New drivers support PXA30X, PXA31X and PXA32X;
6 - Added the support to the flash chips from ESI;
7 - Updated some error messages;


Download (Plz download both part1 & part2 & part3, then unzip together.):

Attachment: H-JTAG V1.1 Release.part01.rar (2010-7-26 20:21, 1.5 M)
Download count 3439


Attachment: H-JTAG V1.1 Release.part02.rar (2010-7-26 20:21, 1.5 M)
Download count 3623


Attachment: H-JTAG V1.1 Release.part03.rar (2010-7-26 20:21, 1.19 M)
Download count 2748


IMPORTANT NOTES:
1 - To debug CORTEX-M3, please use IAR 5.11 and above;
2 - Can't debug CORTEX-M3 with KEIL, because the RDI interface of KEIL is not updated to supported CORTEX-M3;
3 - For STM32F, please configue TAP according to the following pic, otherwise, can't debug;
4 - To use auto flash download, please disable Use Flash Loader in IAR (shown below)

[ Last edited by  twentyone at 2010-7-26 20:25 ]

Hi

good news for H-JTAG supports Cortex-m3.  from i testing. H-JTAG can detect my STM32 Board ( STM32F103RBT6 )  but when i tried to use H-Flash, it can't check target, program, erase or check blank.

Did you configure TAP in H-JTAG server as shown in the above picture? Thx

How can I add the Samsung ARM 11 core / SMDK6400 develoment board?

The JTAG cable on H-JTAG reports 0x00EB509D with a debug jumper in one position and 0x0123BFA0 in the other position.

Do I need to add the two transistors to parallel JTAG cable interface to 20 pin target for TRST and SRST? Or are those signals optional?
TMS, TCK, TDI and TDO are wired via a LS244 buffer (pins 3,4,5 & 11) powered from USB socket

TRST and SRST are optional.

Hi twentyone

I configure TAP in H-JTAG server same your picture already.




[ Last edited by  nooknikz at 2008-7-25 13:26 ]

Hi nooknikz

I have one more question. Is the flash blank? Thx

็Hi twentyone

This problem have solved. i used other programmer (ULINK) erase flash (flash blank) before, then test with H-JTAG again, now it work!!

I think it have problem with my .hex (Keil Realview) that i had flash to my board before i test this board with H-Jtag.

Hi

I have not got automatic download to work in IAR. When i download bin file manually with H-flasher and attach IAR debugger to running target debugging works fine.  

Any help?

1 - You need to enable auto flash download, H-JTAG -> FLASHER -> AUTO DOWNLOAD
2 - Select the right flash in H-Flasher

Than try again. Please let me know whether it works or not.

By the way, what's the type of your target, ARM7, ARM9 or CORTEX-M3?

Thx

Hi

Yes the autoflasher is enabled, but doesn't work. prosessor is STM32, so Cortex-M3. There is no error message from IAR, it just get stuck. I think IAR is waiting something.

From debug log.
H-JTAG Debug Interface for ARM In-Circuit Emulation.
Thu Jul 31 10:50:34 2008: 43188 bytes downloaded (38.03 Kbytes/sec)
Thu Jul 31 10:50:34 2008: Loaded debugee: C:\Program Files\IAR Systems\Embedded Workbench 5.0 Kickstart\ARM\config\flashloader\ST\FlashSTM32F10x.out
Thu Jul 31 10:50:34 2008: Target reset
Thu Jul 31 10:55:09 2008: Fatal error: WinRDI Go Error

Killed target connection so fatal error

A few questions
1 - You are using STM32F or LM3S from Luminary?
2 - Could you generate a HEX file and send it to me? I want to check the address. To generate the HEX file, you can cinfigure IAR like this:
IAR -> PROJECT -> OPTIONS -> OUTPUT CONVERTER -> GENERATE ADDITIONAL OUTPUT -> INTEL ...
3 - If possible, zip your whole project and send a copy to me. So, I can check everything and figure out where is the issue.

My email address is twentyone@hjtag.com

Thx a lot.

I got your email. I checked the address extacted from your HEX file. It seems ok. Could you change your IAR option and try again. Please change the option as follow:

IAR -> PROJECT -> OPTIONS -> DEBUGGER -> DOWNLOAD -> DE-TICK ALL.

Please de-tick Use Flash Loader in IAR.

[ Last edited by  twentyone at 2008-7-31 19:01 ]

Has anyone managed to program the flash in any of the newer Luminary Micros parts with 256K of flash?  I tried making the obvious edits to the LM3S101 file provided, but no luck.

My LM3S6911-based board fails to communicate at all over JTAG using Luminary's programmer and software, but HJTAG succeeds in recognising the device using an LPT-port JTAG adapter. That's why I hoped HJTAG might work where LMFlash had failed.

Thanks,

    Michael A

Send me an email. I will send you a beta version with the support to LM3S6911. Thx

Hi ,

I have a development board that a i buy from olimex.com with stm32 but i cant connect them with h-tag can you help me?? i have the tap configuration like you said...but doesnt work the error is "unable to find target: please make sure that the hardware is properly connected and power up", i use a usb-jtag from olimex iis some other option?

can some one help me?

Best regards

Sorry, H-JTAG doesn't support USB-JTAG.

Has not to download